QF In Cut 45®

Nordfab manufactures ducting for use in dust, mist, and fume collection systems.

Quick-Fit® In Cuts, also known as Saddle Taps, are standard with QF rolled ends, allowing quick connections with other QF® ductwork. Used to cut into existing duct lines to begin a new Quick-Fit (QF) section.

When ordering, specify material; gauge (if nonstandard); dimensions A and C; and end styles if not all QF.
Saddle length and width = 3" all directions from Branch Tube C
Available in galvanized steel and 304SS (as shown below) or optional 316SS or carbon steel
Available with 30° angle
Available with flanged ends in diameters up to 72", and other various end types
Optional gauges 18, 16, 14, 12 and 10

Contact Nordfab or your local Nordfab dealer for assistance with optional end types, larger sizes, and material / gauge options.

Quick-Fit has been used in a wide variety of applications, wherever dust collection or fine particulate transfer is required. Quick-Fit saves time and money on installation, is easy to clean out, is adaptable to existing ductwork, and is easily re-used during shop floor reconfigurations. Learn more about why Quick-Fit may be the best solution for you.

สเปคสินค้า

A. General Fabrication Requirements: Comply with SMACNA's "HVAC Duct Construction Standards - Metal and Flexible," Ch. 3, "Round, Oval, and Flexible Duct," based on indicated static-pressure class unless otherwise indicated.
1. Construct ducts of galvanized sheet steel unless otherwise indicated. 304SS Optional.
2. Basis-of-Design Product: Subject to compliance with requirements, provide Nordfab Ducting, LLC; Quick Fit (QF) Duct.
B. Connection Joints: Joint types are fabricated in accordance with SMACNA's "HVAC Duct Construction Standards - Metal and Flexible," for static-pressure class, applicable sealing requirements, materials involved, duct-support intervals, and other provisions in SMACNA's "HVAC Duct Construction Standards - Metal and Flexible."
1. Quick Fit Joints in Ducts 3 to 24 inches (76 to 510 mm) in diameter. Flange: Optional.
2. Flanged Joints in All Ducts Greater than 24 inches (610 mm) in diameter.
C. Longitudinal Seams: Seam types are fabricated in accordance with SMACNA's "HVAC Duct Construction Standards - Metal and Flexible," Figure 3-2, "Round Duct Longitudinal Seams," for static-pressure class, applicable sealing requirements, materials involved, duct-support intervals, and other provisions in SMACNA's "HVAC Duct Construction Standards - Metal and Flexible."
1. Fabricated round ducts 3 to 24 inches (76 to 510 mm) in diameter to have laser-welded or plasma-welded longitudinal seams.
2. Fabricated round ducts above 24 inches (610 mm) in diameter to have plasma-welded longitudinal seams.

สเปคสินค้าด้านเทคนิค

Unique ref.us-qf-in-cut-45-degree
Product familyQuick-Fit Clamp Together Ducting
กลุ่มผลิตภัณฑ์Branches
ประเภทวัตถุ (วัตถุชิ้นเดียว)
วันที่เผยเเพร่2024-05-08
หมายเลขฉบับ1

ลิงค์

Product urlhttps://www.nordfab.com/en-us/products/qf-ducting/branches/us-qf-in-cut-45-degree
ข้อมูลด้านเทคนิคhttps://www.nordfab.com/-/media/files/nordfab/americas/americas-product-data-sheets/nordfab_in-cut.pdf

สิ่งที่เกี่ยวข้อง

วัสดุหลักGalvanized steel
วัสดุรองStainless steel 304
ออกเเบบโดยสหรัฐอเมริกา
ผลิตโดยสหรัฐอเมริกา

การจำแนกประเภท

หมวดหมู่ BIMobjectงานระบบ (HVAC) - Dust Collection
IFC classificationDuct Fitting
ETIM CodeEG015540
ETIM NameFittings, flanges and connectors
Uniclass 2015 CodePr_65_65_25
Uniclass 2015 DescriptionDuctwork and fittings
CSI MasterFormat 2014 Code23 31 13.19
CSI MasterFormat 2014 TitleMetal Duct Fittings
OmniClass Number23-33 49 00
OmniClass TitleHVAC Ductwork

พื้นที่การขาย

อเมริกาเหนือ
คอสตาริกา
แคนาดา
แซงมาร์แตง
เบลีซ
เบอร์มิวดา
ปานามา
เปอร์โตริโก
เม็กซิโก
สหรัฐอเมริกา
หมู่เกาะบริติชเวอร์จิน