Single Stage Infrared Heater, Model UXR

Includes all of the features in a Model UX plus... the burner box is sealed for rugged, harsh environments and heat-treated aluminized is standard tube supplied. CSA approved for outdoor use.

Approved for outdoor use
40,000 to 220,000 btu/h
Natural gas and LPG
Configurations of "U" and "L", horizontal or 45°
Separated controls compartment – electronics out of air stream, burner can run during servicing
Self diagnostic ignition module
Parabolic aluminum reflectors – most efficient in industry
Direct spark ignition
Vented or unvented
Operating status light
Low voltage controls
Jet stream burner – improved heat distribution, better combustion
Heavy duty couplings – no leaks, cannot be over tightened
UXR features burner box sealed for outdoor conditions
Rubber gaskets
Silicone used to seal corners and joints
Weather resistant electrical components used for exterior connections
Stainless steel burner boxes available as well as tubing and reflectors
Units are wind resistant
Three year warranty on all components
Seven year warranty on aluminized heat exchanger
10 year warranty on aluminized heat exchanger with post purge feature

Voce di capitolato

Low-Intensity Single Stage Infrared Tube Heaters with minimum 65% radiant factor as determined by independent lab testing to EN416-2 Standard. Baffles required as per manufacturer’s instructions.
Assemblies shall be CSA approved low-intensity heater to the latest ANSI Z83.20 and CSA 2.34 for use in commercial and industrial applications. Burner shall be a positive pressure burner system, where exhaust gases and other products of combustion are not routed through the blower. The burner shall operate at a minimum gas inlet pressure of 5.0 inches W.C. (natural gas) or 11.5 inches W.C. (propane) and draw no more than 1 Amp at 120VAC, 60Hz.
Burner head shall be chrome-plated steel and burner controls shall be located outside of the air supply stream to allow service and diagnostic control checks with the burner operating. Reflector shall be a 10-sided reflector design reflecting virtually 100% of the infrared energy out and away from the emitter tubes. Reflector shall be “Deep Dish” design with emitter tubes fully recessed within the reflector. Reflectors with less than 10 surfaces will not be allowed. Reflector shall be mill-finished aluminum, ASTM 1100, .024 inch thick aluminum sheet metal with two reflector support brackets for every 10 feet (3048 mm) reflector section. Reflectors shall extend below the lowest position of the tubing at all times. Reflector end caps shall be fitted to the end of each reflector run to reduce convective heat loss and shall be standard equipment. Emitter Tube shall be 4 inches (102 mm) diameter, minimum 16 gauge thickness. Combustion Tube shall be 4 inches (102 mm) diameter, 16 gauge, heat-treated type 1 aluminized steel tubing shall be required for all firing rates. Hot rolled steel combustion tubing shall not be allowed. Combustion tubing shall incorporate a welded, 11 gauge steel, 4 bolt flange to orient the burner to the tube as designed. Couplings shall be 16 gauge aluminized steel, minimum 12 inches in length, and be of heavy-duty design incorporating two 1-inch wide draw bands.
This product was specified based on best practice design to meet the specific engineered design criteria for this project.
Any submission for substitution must include the following material for consideration or bid will be deemed unqualified and rejected:
- Independent lab testing to EN416-2 standard dated no later than 6 months from date of submission showing a minimum 65% radiant factor
- Professional Engineer Stamped Design, calculations, and complete set of stamped drawings with alternate systems.
- Stamped fuel usage data showing a minimum 20% fuel savings over specified Superior Radiant Model
- Verification that Manufacturer successfully completed and passed the auditing requirements for ISO 9001 Quality Management System (QMS).

Specifiche tecniche

Rif. Unicouxr
Famiglia di prodottoSingle Stage Infrared Heaters
Gruppo di famigliaLow Intensity - Series U
TipoOggetto (oggetto singolo)
Data di pubblicazione2021-02-16
Numero di versione1

Links

Link al Prodottohttps://www.superiorradiant.com/index.php/products/single-stage-infrared-tube-heaters/low-intensity/rugged-high-efficiency-heater
Istruzioni di installazionehttp://bit.ly/2tnaXyv
Certificazione di Prodottohttps://www.csagroup.org/testing-certification/product-listing/certificate/?cert=112168_0_000-2902-09
Descrizione Tecnicahttp://bit.ly/2uhjBTA

Relativo a

Materiale principaleAcciaio
Materiale secondarioAlluminio
Progettato inCanada
Prodotto inCanada

Classificazioni

Categoria BIMobjectRiscaldamento, ventilazione e condizionamento - Riscaldatori e radiatori
Nome UNSPSCTubular heaters
Codice UNSPSC40101822
Codice Uniclass 2015Pr_70_60_36_72
Descrizione Uniclass 2015Radiant tube heaters
Codice CSI MasterFormat 201423 55 23
Titolo CSI MasterFormat 2014Gas-Fired Radiant Heaters
Numero OmniClass23-33 15 17 13
Titolo OmniClassFuel Fired HVAC Radiant Heaters
Codice CSI UniFormat IID30
Titolo CSI UniFormat IIHVAC

Disponibilità Regionale

Nord America
Anguilla
Antigua e Barbuda
Aruba
Bahamas
Barbados
Belize
Bermuda
Canada
Costa Rica
Cuba
Curaçao
Dominica
El Salvador
Giamaica
Grenada
Groenlandia
Guadalupa
Guatemala
Haiti
Honduras
Isole BES
Isole Cayman
Isole Turks e Caicos
Isole Vergini Americane
Isole Vergini britanniche
Martinica
Messico
Montserrat
Nicaragua
Panamá
Porto Rico
Repubblica Dominicana
Saint Kitts e Nevis
Saint Martin
Saint Vincent e Grenadine
Saint-Barthélemy
Saint-Pierre e Miquelon
Santa Lucia
Sint Maarten
Stati Uniti
Trinidad e Tobago